Project Badgermascus – Part 6 – Trials and Tribulations

I have spent both Monday and Tuesday finishing flattening, drilling, and fitting the handle scales and the brass fittings.

© Charly, all rights reserved. Click for full size.

First I have sieved some bone dust that I have collected through a fine nylon mesh (from pantyhose – I do not wear them, but they can be quite useful in the workshop, so I have indeed several in a drawer). I mixed then the bone dust with five-minute epoxy, filled the hollow back of the bones with it and heated it with a heat gun to about 70°C (not so hot you cannot touch it, but hot enough you cannot press your hand against it for a longer time, a hairdryer would suffice too for this particular task) for quicker curing and stronger bond.

After it completely hardened I ground the back flat again and proceeded to drill the holes for pins.

© Charly, all rights reserved. Click for full size.

Drilling the holes was relatively uneventful. Double-sided tape was very useful in holding the scale on the tang and the whole assembly on a flat piece of wood for drilling to avoid chipping of the bone on exit. Also, I have used blunted and overheated drill bits to hold the scales in place for a good fit and I did not mess up the job terribly. I did make minor mistakes on the left handle scale, but those should be correctable when fixing everything together.

With the scales drilled and fitted against the bolster, I proceeded to make the brass pommel fittings. That went really well, and everything went smoothly. Too smoothly you might say. I glued the brass fittings in place, peened the pins and ground, and polished them over.

That is where the problems started, and I must say – they are not all my fault.

The first problem was that the round stock I have used for pins apparently has different chemical composition than the flat profile used for fittings. Had I known this, I would not file them flush and I would leave them slightly proud of the surface (“admitted” instead of “hidden”). However, there was no way back once I ground them flush, so I was hoping they will get hidden under the patina.

But the patining did not go well too, in three ways.

© Charly, all rights reserved. Click for full size.

The first  – I have made a mistake – I have not masked the steel properly. I thought I did, but I just did not. And as one Czech rather rude but astute saying goes – ” myslet znamená hovno vědět” – “to think (assume/mean/guess) means to know shit-all”. So when I was giving the brass a nice hot bath to copper plate it, some of that bath leaked under the masking and copper-plated and etched the blade in some places too.

The second – the different brasses did not take copper plating identically, it was a lot more difficult to copper plate the pins than the rest. It took over an hour to do on the pins what took mere minutes on the rest (which exacerbated the problem with poor masking later on).

The third – when blackening, I have made the solution probably way too concentrated. It has covered the parts in a nice jet-black matt color almost instantly. But that color has completely rubbed off when I washed it with water and brush. I did not realize the true cause of this so I tried it two more times, but it just did not take, especially not on the pins, After the third attempt I thought I am done on the pommel at least, but it flaked off the next day again.

These mistakes are not catastrophic, but they are a major setback. I had to re-polish everything (done), re-etch with ferric chloride (done), give the steel new tannic-acid patina (in progress), and only after that is done to my satisfaction, can I again try to patina the brass.

However, I have to deal somehow with the pins now. They are ground flush already, but since they will not take the patina the same way the rest does, I must leave them visible. And that means probably leaving them polished and not applying patina to them at all. I will do that and then I will decide whether I like it or not. If not, then I will have to drill them out and either replace them or, if I bungle that job (which is very likely) to make completely new fittings. Either way, it is at least one day, and possibly several days, of work before I can progress further.

However, there did come one good thing out of this – I found two new recipes for black that do not require copper-plating the brass first. One requires hot-bath with ammonia (CuSO4+Na2CO3 – precipitates basic copper carbonate which after filtering and washing with water can be dissolved in hot water by adding ammonia), so it is a major stink and not exactly easy or quick. The second one works at room temperature but is rather caustic and dangerous to handle (HCl + potassium polysulfide). I will probably try the second one now, although I do not like very much working with caustic solutions, since my equipment, as you have seen, is not exactly suited for that kind of job.

Resin Art: there’s different roads to success, but infinite ways to fuck up

Remember the seashell resin bowl failure? Of course I didn’t want to leave it at that and made another one. This time I cast it in the early afternoon so I could form it in the late evening. Also the painter’s foil I’d used to pour it on was pretty matte, and I wanted shiny, so I used cling foil again. Well, only that the cling foil melted when I used the heat gun…

I could salvage the result and I actually do like it very much.

©Giliell, all rights reserved

©Giliell, all rights reserved

Only it’s got some gaps and slashes and you should be really careful when you handle it because resin can be sharp as a knife.

Next try: using a non stick baking sheet. That was definetely heat safe. But, you already know there’s a but, it was also quite rigid and didn’t fit the tray I use for pouring well, so the result became smaller and thicker than hoped for. Also they matte surface again.

©Giliell, all rights reserved

©Giliell, all rights reserved

©Giliell, all rights reserved

I had to glue some pebbles into the bottom because it’s asymmetrical, but the overall result is good.

OK, back to square one. Cling foil, no heat gun, just my lung capacity to blow the resin around. But also remember what I did wrong in square one? Right, pour at night, form in the morning. This time it didn’t tear, but it also didn’t move much. The result is so much off balance that I had to put a pound of pebbles into it and still the slightest wind couldmake it fall over

©Giliell, all rights reserved

And now for the last one, poured in the afternoon, no heat gun, on cling foil:

©Giliell, all rights reserved

©Giliell, all rights reserved

Here you can see how soft the resin still was and how easily it shaped. It is the tall, slender, wavy thing I’d been hoping for.

The Art of Book Design: Where the Blue Begins

More allegory than a fairy tale, this book is a delightful dog story filled with the imaginative and charming artwork of Arthur Rackham, one of the great artists of the golden age of book illustration, which lasted from about 1880 to 1920. There are many line drawings throughout the book, but only 4 full-colour illustrations, all of which I’ve attached. Enjoy.

Christopher Morley. Where the Blue Begins. Illustrated by Arthur Rackham. Philadelphia, Lippincott, 1922.

Frontispiece, Where the Blue Begins.

 

Page 28, Where the Blue Begins.

Page 92, Where the Blue Begins.

Page 148, Where the Blue Begins.

 

 

via: The Internet Archive

Cover Photo via Abe Books

Project Badgermascus – Part 5 – Handle Scales

Tomorrow you will get a break from this project, I promise. But today, the Great Flattening from yesterday has continued.

After some deliberations I have decided to try and go for fully blackened brass fittings. That means that the blade will be dark grey, and the fittings really, really dark gray. What kind of handle material should I use? Marcus has sent me a nice piece of stabilized spalted maple, but I do not think it is the right material for this project. Ditto, any of the dark woods that I have. I think the blade deserves the poshest material I have available – bone. I think it will provide a nice contrast to the dark metal.

© Charly, all rights reserved. Click for full size.

Which meant I first had to rough-cut the scales with a hacksaw, which is one hell of a job, let me tell you. Bandsaw or any electrical saw is a big no-no for cutting bone, this has to be done manually. Including pre-cutting he flat sides, before grinding them truly flat.

Thus I had to spend the whole working day with a respirator and my fingers are all sore now. Because the grinding had to be done manually too. Belt sander does work on bone, but it destroys belts way too quickly for my liking and as I learned in the past, these thin flat pieces would have a tendency to be dragged out of my grasp, increasing the risk of injury or bungled work. So flatstone+glue+sandpaper it was. Maybe after I build myself a disk-grinding attachment this work will be easier, but now it is not.

© Charly, all rights reserved. Click for full size.

The scales are ever so slightly bigger than the tang and thicker than the bolster now, and they will remain so. I do not intend for a flush fit, but for a proud one ( I have seen English-speaking knife-makers refer to it as “heirloom fit” although I was not able to find anything specific about it, so I am not sure that is the correct term).

The principle is the same in carpentry – whenever two surfaces join, you can make the joint either hidden or visible, but it should not be visible because you failed to hide it. So if you make it visible, it should be apparent that it was intentional. Like gluing in spacers, making the surfaces meet in a groove and not on a flat, etc.

© Charly, all rights reserved. Click for full size.

Today’s work ended in the kitchen, where the two rough-ground scales ended in a pot at 60°C for an hour or so with circa a teaspoon of washing soda and one spoon of washing powder in 1 l of water to dissolve and wash out as much of remaining fat as possible. In the end I have added a teaspoon of hydrogen peroxide to whiten the bones a bit, although complete whitening is not possible on these.

Tomorrow when they are dry I shall fill the hollows on the inside (where marrow used to be) with epoxy to make them flat. After that, I can start the remaining works, i.e. fit and polish the pommel, drill all the holes, and finally, the glue-up. We will see how that goes.

Project Badgermascus – Part 4 – The Great Flattening

Today I have started the work on the handle, starting with brass fittings. First I have cut four pieces of brass, two for the bolster, two for the pommel, and I drilled 2,5 mm holes in the bolster pieces. On the left piece, I have then cut M3 thread and on the right piece, I have widened the holes to 3 mm.

For pins, I am going to be using a 3 mm brass rod. I cut 4 small pieces and on each, I have made a bit of M3 thread to go into the left side of the bolster (and later on the pommel). The M3 threads are, strictly speaking, unnecessary, but I find they help with two things. First, they help to keep track of which part is left and which is right, so I do not confuse them at some point and make a false cut with a file. Second, fiting the two halves together is easier, because the pins hold fast in place and do not fall off when manhandling the assembly.

I guess these preparations should not take me too long. They took me over five hours. The drilling, cutting etc was not the biggest issue. The biggest issue was the tang. During polishing of the blade it became noticeably thinner, and because the polished area bleeds over to the tang, the tang was not flat anymore – it was a few tenths of a mm thinner at the bolster. So I went and flattened it on a stone.

© Charly, all rights reserved. Click for full size.

As you can see, the tang has relatively deep gashes cut into it with the edge of the grinding wheel. Those are there for three purposes – they reduce the weight, they provide a good grip for the epoxy later on, and they reduce the area that needs to be manually ground off when making the tang flat.

Even so it took me a lot longer than it should have because I did not have the correct sandpaper readily available. What you see here is green corundum, which should be used only dry and only for wood. I have to buy very coarse wet & dry sandpaper, but I keep forgetting and the coarsest I have in stock is 120 grit, which is not nearly enough for this.

© Charly, all rights reserved. Click for full size.

And this is where I am now. Next, I will polish and finish the front side of the bolster but not assemble it. Then I will make the handle scales, fit and drill those, and only after that is done I will drill and fit the pommel part. I have not decided yet whether or not the pommel needs a hole for a lanyard.

The way things are going, I have still quite a few days of work ahead of me.

Project Badgermascus – Interlude 3 – Blackness Achieved!

Kestrel mentioned some commercial blackening compounds containing Tellurium and that train of thought sent me down a path of thinking whether I do or do not have some chemical compound containing sulfur anions, which too react with copper to make a black color. And I realized that I do because a solution of polysulfide is sold as a common fungicide. It does not work on brass directly, but if that brass is first coated with copper, then it does work. So I did exactly that, and voila! It takes a long time, but it works.

© Charly, all rights reserved. Click for full size.

It is not pitch-black, it has a bit of bluish-grey tint to it, but under a coat of wax or lacquer, it would be a lot darker. I consider it a definitive success.

I am wondering whether it would be possible to make pictures on brass with different patinas. As a kind of colored etching process. I do not see a reason why that should not work.